Raytech TM1030 = Raytech CMF-300 Magnetic Tumbler Raytech TM1030 = Raytech CMF-300 Magnetic Tumbler Raytech TM1030 = Raytech CMF-300 Magnetic Tumbler Raytech TM1030 = Raytech CMF-300 Magnetic Tumbler
Raytech TM1030 = Raytech CMF-300 Magnetic Tumbler Raytech TM1030 = Raytech CMF-300 Magnetic Tumbler Raytech TM1030 = Raytech CMF-300 Magnetic Tumbler Raytech TM1030 = Raytech CMF-300 Magnetic Tumbler

TM1030 = Raytech CMF-300 Magnetic Tumbler

$299.95
+ -
Add to cart
Article number: TM1030
Availability: In stock

CENTRIFUGAL MAGNETIC FINISHER
Magnetic finishing presents itself as the pinnacle of methods to efficiently burnish and polish small non-ferrous metals such as gold and silver. With steel media as small as .010" in diameter and .25" in length, this finisher is able to work in areas such as undercuts, recesses, slots, etc. No other method works as well.


Centrifugal magnetic tumbler is quiet compared to other forms of finishing. Typically on soft, non-ferrous metals, the finishing cycle can be as short as 30 minutes. This alone assures a faster turn around time on parts compared to any other method.

Centrifugal magnetic finishing addresses the most intricate and detailed parts imaginable.

It should be noted that on any large, smooth, flat surfaces the finish will appear frosted. A light buffing or a run through a dry tumbler is recommended.

A centrifugal magnetic finisher is a direct drive, fan cooled design. The magnetic disk is made up of many powerful magnets that are precisely placed on a cast disk. The alternating polarity is constantly changing, thereby allowing the media to move freely in a liquid solution that is constantly changing its makeup. This combined with the centrifugal force allows for super quiet and fast time cycles.

Raytech’s smallest capacity magnetic finisher has a 3-inch (76.2mm) diameter chamber that finishes the equivalent of 1 to 6 rings. Pin capacity 30-50 grams (1.0 – 1.75 ounces) depending on the needs of the user and material/parts being finished. The CMF-300 has a fixed speed with mechanical timer and molded bowl and cover. Use only Stainless Steel Pin media.  Use with Raytech Compound M Solution.  Not for use with dry bowls media.

Magnetic pins are NOT included.

How does a magnetic tumbler work?
A magnetic tumbler uses thousands of teeny tiny little steel pins to do its job.  These pins (just a fraction of a millimeter in diameter) act like thousands of little hammers that pound against the surface of your jewelry.  They are burnishing your pieces but on a very small scale. The pins can get into the smallest and crevices.  The result is a piece that is bright and shiny, work-hardened and finished while you did other work, and its all done more quickly that rotary or vibratory tumblers.  Also there is no loss of metal since the burnishing is not an abrasive process.

Tips on Using Your Magnetic Tumbler

*Do not use all the shot provided with the unit at once. There is always a bit of experimentation involved in the first few uses. As a starting point, place approximately 1/4 lb of the stainless steel shot in the plastic container for every 10 rings.

*After you have placed the shot in the bowl, fill it with water to between 1/3 and 1/2 full.

*Put tumbling soap / burnishing solution in the water.

*Put in your jewelry and run the machine for about 40 minutes.

*After your first "tumble", you should have an understanding of what you have to do to obtain the finish you require. Once you have established the proportions and tumbling times that give you the desired results, you will be able to consistently obtain the same results over and over.

0 stars based on 0 reviews
Add to wishlist / Add to compare